The ungleich ceph handbook » History » Revision 62
« Previous |
Revision 62/73
(diff)
| Next »
Nico Schottelius, 05/28/2022 08:47 PM
The ungleich ceph handbook¶
- Table of contents
- The ungleich ceph handbook
- Status
- Introduction
- Processes
- Communication guide
- Analysing
- Adding a new disk/ssd to the ceph cluster
- Moving a disk/ssd to another server
- OSD related processes
- Change ceph speed for i/o recovery
- Debug scrub errors / inconsistent pg message
- Move servers into the osd tree
- How to fix existing osds with wrong partition layout
- How to fix unfound pg
- Phasing out OSDs
- Enabling per image RBD statistics for prometheus
- S3 Object Storage
- Debugging ceph
- Performance Tuning
- Ceph theory
Status¶
This document is IN PRODUCTION.
Introduction¶
This article describes the ungleich storage architecture that is based on ceph. It describes our architecture as well maintenance commands. Required for
Processes¶
Usage monitoring¶
- Usage should be kept somewhere in 70-75% area
- If usage reaches 72.5%, we start reducing usage by adding disks
- We stop when usage is below 70%
Phasing in new disks¶
- 24h performance test prior to using it
Phasing in new servers¶
- 24h performance test with 1 ssd or 1 hdd (whatever is applicable)
Communication guide¶
Usually when disks fails no customer communication is necessary, as it is automatically compensated/rebalanced by ceph. However in case multiple disk failures happen at the same time, I/O speed might be reduced and thus customer experience impacted.
For this reason communicate whenever I/O recovery settings are temporarily tuned.
Analysing¶
ceph osd df tree¶
Using ceph osd df tree you can see not only the disk usage per OSD, but also the number of PGs on an OSD. This is especially useful to see how the OSDs are balanced.
Find out the device of an OSD¶
Use mount | grep /var/lib/ceph/osd/ceph-OSDID on the server on which the OSD is located:
[16:01:23] server2.place6:~# mount | grep /var/lib/ceph/osd/ceph-31 /dev/sdk1 on /var/lib/ceph/osd/ceph-31 type xfs (rw,relatime,attr2,inode64,noquota)
Show config¶
ceph config dump
Show backfill and recovery config¶
ceph-conf --show-config | egrep "osd_recovery_max_active|osd_recovery_op_priority|osd_max_backfills"
Adding a new disk/ssd to the ceph cluster¶
write on the disks, which order / date we bought it with a permanent marker.
Checking the shadow trees¶
To be able to spot differences / weights of hosts, it can be very helpful to look at the crush shadow tree
using ceph osd crush tree --show-shadow:
-16 hdd-big 653.03418 root default~hdd-big -34 hdd-big 0 0 host server14~hdd-big -38 hdd-big 0 0 host server15~hdd-big -42 hdd-big 81.86153 78.28352 host server17~hdd-big 36 hdd-big 9.09560 9.09560 osd.36 59 hdd-big 9.09499 9.09499 osd.59 60 hdd-big 9.09499 9.09499 osd.60 68 hdd-big 9.09599 8.93999 osd.68 69 hdd-big 9.09599 7.65999 osd.69 70 hdd-big 9.09599 8.35899 osd.70 71 hdd-big 9.09599 8.56000 osd.71 72 hdd-big 9.09599 8.93700 osd.72 73 hdd-big 9.09599 8.54199 osd.73 -46 hdd-big 90.94986 90.94986 host server18~hdd-big ...
Here we can see that the weight of server17 for the class hdd-big is about 81, the one of server18 about 90.
SSDs and other classes have their own shadow trees, too.
For Dell servers¶
First find the disk and then add it to the operating system
megacli -PDList -aALL | grep -B16 -i unconfigur # Sample output: [19:46:50] server7.place6:~# megacli -PDList -aALL | grep -B16 -i unconfigur Enclosure Device ID: N/A Slot Number: 0 Enclosure position: N/A Device Id: 0 WWN: 0000000000000000 Sequence Number: 1 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 894.252 GB [0x6fc81ab0 Sectors] Non Coerced Size: 893.752 GB [0x6fb81ab0 Sectors] Coerced Size: 893.75 GB [0x6fb80000 Sectors] Sector Size: 0 Firmware state: Unconfigured(good), Spun Up
Then add the disk to the OS:
megacli -CfgLdAdd -r0 [Enclosure Device ID:slot] -aX (X : host is 0. md-array is 1) # Sample call, if enclosure and slot are KNOWN (aka not N/A) megacli -CfgLdAdd -r0 [32:0] -a0 # Sample call, if enclosure is N/A megacli -CfgLdAdd -r0 [:0] -a0
Then check disk
fdisk -l [11:26:23] server2.place6:~# fdisk -l ...... Disk /dev/sdh: 7.3 TiB, 8000987201536 bytes, 15626928128 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [11:27:24] server2.place6:~#
Then create gpt
/opt/ungleich-tools/disk-create-fresh-gpt /dev/XXX [11:31:10] server2.place6:~# /opt/ungleich-tools/disk-create-fresh-gpt /dev/sdh ...... Created a new DOS disklabel with disk identifier 0x9c4a0355. Command (m for help): Created a new GPT disklabel (GUID: 374E31AD-7B96-4837-B5ED-7B22C452899E). ......
Then create osd for ssd/hdd-big
/opt/ungleich-tools/ceph-osd-create-start /dev/XXX XXX(sdd or hdd-big) [11:33:58] server2.place6:~# /opt/ungleich-tools/ceph-osd-create-start /dev/sdh hdd-big + set -e + [ 2 -lt 2 ] ...... + /opt/ungleich-tools/monit-ceph-create-start osd.14 osd.14 [ ok ] Restarting daemon monitor: monit. [11:36:14] server2.place6:~#
Then check rebalancing(if you want to add another disk, you should do after rebalancing)
ceph -s
[12:37:57] server2.place6:~# ceph -s
cluster:
id: 1ccd84f6-e362-4c50-9ffe-59436745e445
health: HEALTH_WARN
2248811/49628409 objects misplaced (4.531%)
......
io:
client: 170KiB/s rd, 35.0MiB/s wr, 463op/s rd, 728op/s wr
recovery: 27.1MiB/s, 6objects/s
[12:49:41] server2.place6:~#
Moving a disk/ssd to another server¶
(needs to be described better)
Generally speaking:
- //needs to be tested: disable recovery so data wont start move while you have the osd down
- /opt/ungleich-tools/ceph-osd-stop-disable does the following:
- Stop the osd, remove monit on the server you want to take it out
- umount the disk
- Take disk out
- Discard preserved cache on the server you took it out
- using megacli:
megacli -DiscardPreservedCache -Lall -aAll
- using megacli:
- Insert into new server
- Clear foreign configuration
- using megacli:
megacli -CfgForeign -Clear -aAll
- using megacli:
- Disk will now appear in the OS, ceph/udev will automatically start the OSD (!)
- No creating of the osd required!
- Verify that the disk exists and that the osd is started
- using ps aux
- using ceph osd tree
- /opt/ungleich-tools/monit-ceph-create-start osd.XX # where osd.XX is the osd + number
- Creates the monit configuration file so that monit watches the OSD
- Reload monit
- Verify monit using monit status
OSD related processes¶
Removing a disk/ssd¶
To permanently remove a failed disk from a cluster, use ceph-osd-stop-remove-permanently from ungleich-tools repo. Warning: if the disk is still active, the OSD will be shutdown AND removed from the cluster -> all data of that disk will need to be rebalanced.
Handling DOWN osds with filesystem errors¶
If an email arrives with the subject "monit alert -- Does not exist osd.XX-whoami", the filesystem of an OSD cannot be read anymore. It is very highly likely that the disk / ssd is broken. Steps that need to be done:
- Login to any ceph monitor (cephX.placeY.ungleich.ch)
- Check ceph -s, find host using ceph osd tree
- Login to the affected host
- Run the following commands:
- ls /var/lib/ceph/osd/ceph-XX
- dmesg
ex) After checking message of dmesg, you can do next step [204696.406756] XFS (sdl1): metadata I/O error: block 0x19100 ("xlog_iodone") error 5 numblks 64 [204696.408094] XFS (sdl1): xfs_do_force_shutdown(0x2) called from line 1233 of file /build/linux-BsFdsw/linux-4.9.65/fs/xfs/xfs_log.c. Return address = 0xffffffffc08eb612 [204696.410702] XFS (sdl1): Log I/O Error Detected. Shutting down filesystem [204696.411977] XFS (sdl1): Please umount the filesystem and rectify the problem(
- Create a new ticket in the datacenter light project
- Subject: "Replace broken OSD.XX on serverX.placeY.ungleich.ch"
- Add (partial) output of above commands
- Use /opt/ungleich-tools/ceph-osd-stop-remove-permanently XX, where XX is the osd id, to remove the disk from the cluster
- Remove the physical disk from the host, checkout if there is warranty on it and if yes
- Create a short letter to the vendor, including technical details a from above
- Record when you sent it in
- Put ticket into status waiting
- If there is no warranty, dispose it
Create new pool and place new osd¶
Configuring auto repair on pgs¶
ceph config set osd osd_scrub_auto_repair true
Verify using:
ceph config dump
Change ceph speed for i/o recovery¶
By default we want to keep I/O recovery traffic low to not impact customer experience. However when multiple disks fail at the same point, we might want to prioritise recover for data safety over performance.
The default configuration on our servers contains:
[osd] osd max backfills = 1 osd recovery max active = 1 osd recovery op priority = 2
The important settings are osd max backfills and osd recovery max active, the priority is always kept low so that regular I/O has priority.
To adjust the number of backfills per osd and to change the number of threads used for recovery, we can use on any node with the admin keyring:
ceph tell osd.* injectargs '--osd-max-backfills Y' ceph tell osd.* injectargs '--osd-recovery-max-active X'
where Y and X are the values that we want to use. Experience shows that Y=5 and X=5 doubles to triples the recovery performance, whereas X=10 and Y=10 increases recovery performance 5 times.
Debug scrub errors / inconsistent pg message¶
From time to time disks don't save what they are told to save. Ceph scrubbing detects these errors and switches to HEALTH_ERR. Use ceph health detail to find out which placement groups (pgs) are affected. Usually a ceph pg repair <number> fixes the problem.
If this does not help, consult https://ceph.com/geen-categorie/ceph-manually-repair-object/.
Move servers into the osd tree¶
New servers have their buckets placed outside the default root and thus need to be moved inside.
Output might look as follows:
[11:19:27] server5.place6:~# ceph osd tree ID CLASS WEIGHT TYPE NAME STATUS REWEIGHT PRI-AFF -3 0.87270 host server5 41 ssd 0.87270 osd.41 up 1.00000 1.00000 -1 251.85580 root default -7 81.56271 host server2 0 hdd-big 9.09511 osd.0 up 1.00000 1.00000 5 hdd-big 9.09511 osd.5 up 1.00000 1.00000 ...
Use ceph osd crush move serverX root=default (where serverX is the new server),
which will move the bucket in the right place:
[11:21:17] server5.place6:~# ceph osd crush move server5 root=default
moved item id -3 name 'server5' to location {root=default} in crush map
[11:32:12] server5.place6:~# ceph osd tree
ID CLASS WEIGHT TYPE NAME STATUS REWEIGHT PRI-AFF
-1 252.72850 root default
...
-3 0.87270 host server5
41 ssd 0.87270 osd.41 up 1.00000 1.00000
How to fix existing osds with wrong partition layout¶
In the first version of DCL we used filestore/3 partition based layout.
In the second version of DCL, including OSD autodection, we use bluestore/2 partition based layout.
To convert, we delete the old OSD, clean the partitions and create a new osd:
Inactive OSD¶
If the OSD is not active, we can do the following:
- Find the OSD number: mount the partition and find the whoami file
root@server2:/opt/ungleich-tools# mount /dev/sda2 /mnt/ root@server2:/opt/ungleich-tools# cat /mnt/whoami 0 root@server2:/opt/ungleich-tools# umount /mnt/
- Verify in the ceph osd tree that the OSD is on that server
- Deleting the OSD
- ceph osd crush remove $osd_name
- ceph osd rm $osd_name
Then continue below as described in "Recreating the OSD".
Remove Active OSD¶
- Use /opt/ungleich-tools/ceph-osd-stop-remove-permanently OSDID to stop and remove the OSD
- Then continue below as described in "Recreating the OSD".
Recreating the OSD¶
- Create an empty partition table
- fdisk /dev/sdX
- g
- w
- Create a new OSD
- /opt/ungleich-tools/ceph-osd-create-start /dev/sdX CLASS # use hdd, ssd, ... for the CLASS
How to fix unfound pg¶
refer to https://redmine.ungleich.ch/issues/6388
- Check health state
- ceph health detail
- Check which server has that osd
- ceph osd tree
- Check which VM is running in server place
- virsh list
- Check pg map
- ceph osd map [osd pool] [VMID]
- revert pg
- ceph pg [PGID] mark_unfound_lost revert
Phasing out OSDs¶
- Either directly via /opt/ungleich-tools/ceph/ceph-osd-stop-remove-permanently
- Or first draining it using
ceph osd crush reweight osd.XX 0- Wait until rebalance done
- Then remove
Enabling per image RBD statistics for prometheus¶
[20:26:57] red2.place5:~# ceph config set mgr mgr/prometheus/rbd_stats_pools "one,hdd" [20:27:57] black2.place6:~# ceph config set mgr mgr/prometheus/rbd_stats_pools "hdd,ssd"
S3 Object Storage¶
This section is * UNDER CONTRUCTION *
Introduction¶
- See the Red Hat manual
- The ceph docs about object storage
Architecture¶
- S3 requests are handled by a publicly accessible gateway, which also has access to the ceph cluster.
- s3 buckets are usually
Authentication / Users¶
- Ceph can make use of LDAP as a backend
- However it uses the clear text username+password as a token
- See https://docs.ceph.com/docs/mimic/radosgw/ldap-auth/
- We do not want users to store their regular account on machines
- For this reason we use independent users / tokens, but with the same username as in LDAP
Creating a user:
radosgw-admin user create --uid=USERNAME --display-name="Name of user"
Listing users:
radosgw-admin user list
Deleting users and their storage:
radosgw-admin user rm --uid=USERNAME --purge-data
Setting up S3 object storage on Ceph¶
- Setup a gateway node with Alpine Linux
- Change do edge
- Enable testing
- Update the firewall to allow access from this node to the ceph monitors
- Setting up the wildcard DNS certificate
apk add ceph-radosgw
Wildcard DNS certificate from letsencrypt¶
Acquiring and renewing this certificate is currently a manual process, as it requires to change DNS settings.
- run certbot
- update DNS with the first token
- update DNS with the second token
Sample session:
s3:/etc/ceph# certbot certonly --manual --preferred-challenges=dns --email sre@ungleich.ch --server https://acme-v02.api.letsencrypt.org/directory --agree-tos -d *.s3.ungleich.ch -d s3.ungleich.ch Saving debug log to /var/log/letsencrypt/letsencrypt.log Plugins selected: Authenticator manual, Installer None Cert is due for renewal, auto-renewing... Renewing an existing certificate Performing the following challenges: dns-01 challenge for s3.ungleich.ch dns-01 challenge for s3.ungleich.ch - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - NOTE: The IP of this machine will be publicly logged as having requested this certificate. If you're running certbot in manual mode on a machine that is not your server, please ensure you're okay with that. Are you OK with your IP being logged? - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - (Y)es/(N)o: y - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Please deploy a DNS TXT record under the name _acme-challenge.s3.ungleich.ch with the following value: KxGLZNiVjFwz1ifNheoR_KQoPVpkvRUV1oT2pOvJlU0 Before continuing, verify the record is deployed. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Press Enter to Continue - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Please deploy a DNS TXT record under the name _acme-challenge.s3.ungleich.ch with the following value: bkrhtxWZUipCAL5cBfvrjDuftqsZdQ2JjisiKmXBbaI Before continuing, verify the record is deployed. (This must be set up in addition to the previous challenges; do not remove, replace, or undo the previous challenge tasks yet. Note that you might be asked to create multiple distinct TXT records with the same name. This is permitted by DNS standards.) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Press Enter to Continue Waiting for verification... Cleaning up challenges IMPORTANT NOTES: - Congratulations! Your certificate and chain have been saved at: /etc/letsencrypt/live/s3.ungleich.ch/fullchain.pem Your key file has been saved at: /etc/letsencrypt/live/s3.ungleich.ch/privkey.pem Your cert will expire on 2020-12-09. To obtain a new or tweaked version of this certificate in the future, simply run certbot again. To non-interactively renew *all* of your certificates, run "certbot renew" - If you like Certbot, please consider supporting our work by: Donating to ISRG / Let's Encrypt: https://letsencrypt.org/donate Donating to EFF: https://eff.org/donate-le
Debugging ceph¶
ceph status
ceph osd status
ceph osd df
ceph osd utilization
ceph osd pool stats
ceph osd tree
ceph pg stat
How to list the version overview¶
This lists the versions of osds, mgrs and mons:
ceph versions
Listing the "features" of clients, osds, mgrs and mons can be done using ceph features:
[15:32:20] red1.place5:~# ceph features
{
"mon": [
{
"features": "0x3ffddff8ffecffff",
"release": "luminous",
"num": 5
}
],
"osd": [
{
"features": "0x3ffddff8ffecffff",
"release": "luminous",
"num": 44
}
],
"client": [
{
"features": "0x3ffddff8eea4fffb",
"release": "luminous",
"num": 4
},
{
"features": "0x3ffddff8ffacffff",
"release": "luminous",
"num": 18
},
{
"features": "0x3ffddff8ffecffff",
"release": "luminous",
"num": 31
}
],
"mgr": [
{
"features": "0x3ffddff8ffecffff",
"release": "luminous",
"num": 4
}
]
}
How to list the version of every OSD and every monitor¶
To list the version of each ceph OSD:
ceph tell osd.* version
To list the version of each ceph mon:
2
ceph tell mon.* version
The mgr do not seem to support this command as of 14.2.21.
Performance Tuning¶
- Ensure that the basic options for reducing rebalancing workload are set:
osd max backfills = 1 osd recovery max active = 1 osd recovery op priority = 2
- Ensure that osd_op_queue_cut_off is set to high
- Requires OSD restart on change
ceph config set global osd_op_queue_cut_off high
be sure to check your osd recovery sleep settings, there are several
depending on your underlying drives:
"osd_recovery_sleep": "0.000000",
"osd_recovery_sleep_hdd": "0.050000",
"osd_recovery_sleep_hybrid": "0.050000",
"osd_recovery_sleep_ssd": "0.050000",
Adjusting these will upwards will dramatically reduce IO, and take effect
immediately at the cost of slowing rebalance/recovery.
Reference settings from Frank Schilder:
osd class:hdd advanced osd_recovery_sleep 0.050000 osd class:rbd_data advanced osd_recovery_sleep 0.025000 osd class:rbd_meta advanced osd_recovery_sleep 0.002500 osd class:ssd advanced osd_recovery_sleep 0.002500 osd advanced osd_recovery_sleep 0.050000 osd class:hdd advanced osd_max_backfills 3 osd class:rbd_data advanced osd_max_backfills 6 osd class:rbd_meta advanced osd_max_backfills 12 osd class:ssd advanced osd_max_backfills 12 osd advanced osd_max_backfills 3 osd class:hdd advanced osd_recovery_max_active 8 osd class:rbd_data advanced osd_recovery_max_active 16 osd class:rbd_meta advanced osd_recovery_max_active 32 osd class:ssd advanced osd_recovery_max_active 32 osd advanced osd_recovery_max_active 8
(have not yet been tested in our clusters)
Ceph theory¶
How much data per Server?¶
Q: How much data should we add into one server?
A: Not more than it can handle.
How much data can a server handle? For this let's have a look at 2 scenarios:
- How long does it take to compensate the loss of the server?
- Assuming a server has X TiB storage in Y disks attached and a network speed of Z GiB/s.
- And our estimated rebuild goal is to compensate the loss of a server within U hours.
Approach 1¶
Then
Let's take an example:
- A server with
10 disks * 10 TiB= 100 TiB = 100 000 GiB data. It is network connected with 10 Gbit = 1.25 GiB/s. - 100000/1.25 = 80000s = 22.22h
However, our logic assumes that we actually rebuild from the failed server, which... is failed.
Approach 2: calculating with left servers¶
However we can apply our logic also to distribute
the rebuild over several servers that now pull in data from each other for rebuilding.
We need to read the data (100TiB) from other servers and distribute it to new OSDs. Assuming each server has a 10 Gbit/s
network connection.
Now the servers might need to read (get data from other osds) and *write) (send data to other osds). Luckily, networking is 10 Gbit/s duplex - i.e. in both directions.
However how fast can we actually read data from the disks?
- SSDs are in the range of hundreds of MB/s (best case, not necessarily true for random reads) - let's assume
- HDDs are in the range of tenths of MB/s (depending on the work load, but 30-40 MB/s random reads seems realistic)
Further assumptions:
- Assuming further that each disk should be dedicated at least one CPU core.
Disk/SSD speeds¶
- Tuning for #8473 showed that a 10TB HDD can write up to 180-200MB/s when backfilling (at about 70% cpu usage and 20% disk usage), max backfills = 8
- Debugging SSD usage in #8461 showed SSDs can read about 470-520MB/s sequential
- Debugging SSD usage in #8461 showed SSDs can write about 170-280MB/s sequential
- Debugging SSD usage in #8461 showed SSDs can write about 4MB/s RANDOM (need to verify this even though 3 runs showed these numbers)
Ceph theoretical fundament¶
If you are very much into the theoretical fundament of Ceph check out their paper
Updated by Nico Schottelius over 2 years ago · 62 revisions